Home / Tools & DIY · Product overviews / Building Supplies / Material Handling · More from VEVOR
VEVOR LG-022 16ft Drywall Lift: features, specs and who it suits
A red carbon steel drywall lift with a 150 lb capacity, a telescoping arm, a 16 ft reach, a 60° tilting panel and a winch. What the specs mean for ceiling work.
This page contains an affiliate link, marked as such. If you buy through it, Bloiq may earn a commission at no extra cost to you.
The VEVOR LG-022 is a manual drywall lift, also called a panel hoist. It holds a sheet of drywall against a ceiling or high wall so that one person can fasten it, instead of needing a helper to hold up a heavy panel. It reaches up to 16 feet and is made of carbon steel. Here is what the specs mean.
Why a panel lift helps
A full sheet of drywall is awkward as well as heavy, and ceiling work means holding it overhead while driving screws. A lift takes the weight: you crank the panel into position, secure it, then lower the cradle. That is why these hoists are common in renovations and small construction jobs.
Capacity and reach
VEVOR rates the lift at 150 lb (68 kg). That is the figure to compare against the panels you plan to use, and it is worth remembering that thicker or fire-rated board weighs more than standard board. The arm telescopes from 49 to 115 inches (1245 to 2921 mm), and the maximum height is 16 ft (4877 mm), which suits tall ceilings and stair halls as well as standard rooms.
The winch and the cradle
A winch lets you raise the load by turning a handle rather than lifting by hand, which VEVOR says allows one person to install drywall or wood panels. The panel cradle tilts forward or backward by 60° and rotates 360°. In general, a tilting cradle lets you work on flat ceilings, sloped ceilings and walls with the same tool, and rotating it helps line a sheet up with joists.
Stability and moving it around
The lift stands on a wide tripod base with three non-slip, lockable wheels, and the legs lock to give extra support. Wheels make it easy to roll along the room between sheets, and the locks hold it still while you fasten the panel. The listing describes assembly and disassembly without tools. Assembled, it measures about 60.2 x 60.2 x 76.4 inches (153 x 153 x 194 cm) and weighs 80.7 lb (about 37 kg), so it needs floor space as well as a vehicle with room for it.
Who it suits
VEVOR describes it as suitable for both home and commercial use. It makes sense for homeowners hanging a ceiling, renovators and small contractors who often work alone. People who hang drywall only now and then may still prefer it for ceilings, where the hardest part is the lifting.
What to check before you buy
- Panel weight: compare your board's weight against the 150 lb capacity, including any extra sheets or fixtures.
- Ceiling height: the 16 ft maximum should comfortably exceed your highest working point, with room to spare.
- Floor and space: you need a clear, level floor; the base is about 5 ft square.
- Transport: the lift weighs about 81 lb, so check how you will move and carry it.
- Safe use: follow the manual, lock the wheels before lifting, stay clear of the underside of a raised load and wear suitable protective equipment.
- Assembly: check the parts against the manual when it arrives.
The short version
- A manual drywall lift made of carbon steel, rated at 150 lb (68 kg).
- Telescoping arm of 49-115 inches and a 16 ft maximum reach.
- Panel tilts 60° and rotates 360°; winch raises the load.
- Wide tripod base with three lockable wheels and lockable legs.
- Tool-free assembly; about 80.7 lb with a footprint of roughly 5 ft square.
Bloiq is reader-supported. Some links may earn us a commission; it never affects what we write. How we make money.
