Home / Tools & DIY · Product overviews
VEVOR 36 x 18 in Steel Welding Table: features, specs and who it suits
A rolling carbon steel welding table with a 36 x 18 inch top, 94 fixture holes, four tool slots and a listed 1,200 lb load capacity. What its specs mean.
This page contains an affiliate link, marked as such. If you buy through it, Bloiq may earn a commission at no extra cost to you.
The VEVOR Welding Table is a carbon steel workbench on four casters, with a perforated 36 x 18 inch top and a tool tray underneath. It gives welding and metal work a dedicated surface that rolls to where the job is and locks in place. Here is what its specs mean for a home garage or a small workshop.
Why welders work on a steel table
Welding throws off sparks, spatter and a lot of heat, so a wooden bench or a plastic folding table is a poor place for it. Steel doesn't burn, and spatter that lands on it can usually be scraped or ground off. A steel top also lets you clamp parts down firmly and, on most setups, attach the welder's work clamp to the table itself.
VEVOR builds the frame and the top from carbon steel and says the top is treated to resist wear and rust. Like any steel surface, it is still worth keeping dry when not in use.
A 36 x 18 inch top at about 35 inches high
The work surface measures 36 by 18 inches, roughly 91 x 46 cm. That's a compact footprint: VEVOR pitches it at small and detailed parts, such as brackets, hinges, small frames and repair pieces, rather than long sections of tube or large panels. It fits in a single-car garage without taking over the space.
The top sits about 35 inches (around 90 cm) off the floor, which is close to a typical standing workbench height. Most people can weld, grind or assemble at that height without bending far over the work.
Fixture holes and tool slots
The top has 94 round fixture holes, each 5/8 inch (about 16 mm) across, plus four long tool slots near the edges. The holes accept fixture pins, stops and hold-down clamps, so you can square up parts and keep them from moving while you tack them. The slots give clamp jaws something to grab when a hole isn't in the right place.
5/8 inch is a common hole size for welding fixtures, but fixture systems vary, so confirm that any pins or clamps you already own fit before you plan around them.
Load capacity and the lower tray
VEVOR lists a load capacity of up to 1,200 pounds, about 544 kg. That's far more than most hobby projects will ever put on a table this size, and it leaves room for heavier pieces such as small vises, steel plate or engine parts. Spreading heavy items across the top, rather than concentrating them on one corner, is good practice on any workbench.
Below the top, a full-width steel tray holds clamps, magnets, gloves, wire brushes and filler rod, keeping them within reach but off the work surface.
Moving it and putting it together
The table rolls on casters with brakes, so you can push it out of the way when you're done and lock it before you start. A slim handle on one end gives you something to pull on. Casters roll most easily on smooth concrete; rough or cracked floors make any rolling bench harder to move.
It arrives in parts and bolts together in four steps: the handle, the legs, the frame and shelf, and then the wheels. The screws, bolts and nuts are included. Check the manual for the tools you'll need.
Who it suits
It suits metal hobbyists, DIY welders and professionals who want a compact, mobile table for welding, fabrication and repair. It also works as a general steel bench for assembly and grinding in a garage or workshop where space is tight.
What to check before you buy
- Size: compare the 36 x 18 inch top with the parts you usually work on.
- Fixtures: confirm your pins and clamps fit 5/8 inch (16 mm) holes.
- Your floor: smooth, level floors suit casters best.
- Heavy work: keep loads within the listed 1,200 lb.
- Assembly: check the parts list and the tools the manual calls for.
- Your work area: keep flammable materials clear of welding and follow the manuals for your welder and the table.
The short version
- A carbon steel welding table on lockable casters, with a 36 x 18 inch top about 35 inches high.
- 94 fixture holes of 5/8 inch and four tool slots for clamping parts.
- A listed load capacity of up to 1,200 lb, and a top treated to resist wear and rust.
- A lower tool tray, a side handle and bolt-together assembly in four steps.
Bloiq is reader-supported. Some links may earn us a commission; it never affects what we write. How we make money.
