VEVOR 1.2KW Electric Hydraulic Rebar Bender: specs and who it suits

The VEVOR 1.2KW electric hydraulic rebar bender is a hand-held machine for bending reinforcing bar on a building site or in a workshop. Bending rebar by hand or over a pipe is slow and hard on the body, and results vary from bar to bar. This tool uses a hydraulic ram driven by an electric motor, so the same action is repeated with a press of a switch.

What the 1.2KW motor and hydraulics do

A hydraulic bender uses a motor to drive a pump, which pushes fluid against a piston. The piston moves the bending head. Because fluid transmits force evenly, a modest motor can produce a very large force at the head. VEVOR specifies a 1.2KW motor running on 110V power, and says the motor is made with pure copper windings. Copper windings are common in motors and are generally chosen for efficient conduction and a long service life.

VEVOR also says the motor runs only while a bend is in progress. That means less idle running, less noise and less wear than a motor that stays on all day.

Capacity and bending speed

The listing gives a working range of 0.2 to 0.9 inches (4 to 22 mm) bar diameter, with a bend taking roughly 4 to 5 seconds. VEVOR says the bending angle can exceed 90 degrees. In practice, bar grade matters as much as diameter: harder, higher-strength steel needs more force than mild steel of the same size, so check the grade of the bar you plan to bend against the limits in the manual.

The steel bending head frame is described as sturdy, with strong clamping force intended to hold the bar steadily and reduce wasted steel from slipped or poorly formed bends.

The pressure relief valve

After the bend, the hydraulic pressure has to be released before the bar can come out. The machine has a precision pressure relief valve for this. VEVOR says it releases pressure automatically, and that you open the valve to remove the bent steel. Learn the valve's operation from the manual before first use, as the sequence matters in any hydraulic tool.

Size, weight and handling

The bender measures about 24.5 x 6.8 x 7.7 inches (62 x 17 x 20 cm) and weighs 45 lb (about 20 kg). That is portable in the sense of being carried by a person to a job, not light. It has two handles and an operation switch, which VEVOR says allow safe, efficient starting and use. The tool is intended for rebar, steel bar and steel rod in construction work.

Who it suits

It suits contractors, small construction crews, fence and foundation builders, and workshops that bend stirrups, hooks and L-shapes in volume. For a handful of bends a year, a hand tool may be enough; a powered unit makes more sense when the same bend is repeated many times. Always confirm that bends meet the drawings and local building codes for the project.

What to check before you buy

• Bar size and grade: confirm your bars are within 4 to 22 mm and that the manual covers their grade.
• Power supply: the unit is a 110V tool; check your outlet, extension cord and generator capacity.
• Weight: at about 20 kg, plan how it will be carried and positioned.
• Bend shapes: check which bend radii and angles your plans require against what the bending head can form.
• Fluid and upkeep: read the manual on hydraulic fluid, leaks and maintenance.
• Protective gear: follow the manual's guidance on eye, hand and foot protection.

The short version

• A portable electric hydraulic rebar bender with a 1.2KW motor on 110V power.
• Rated for 0.2 to 0.9 inch (4 to 22 mm) bars in about 4 to 5 seconds per bend.
• Bends can exceed 90 degrees, according to VEVOR.
• Precision pressure relief valve; two handles and an operation switch.
• About 45 lb (20 kg) and 24.5 inches long.

Bloiq is reader-supported. Some links may earn us a commission; it never affects what we write. How we make money.