VEVOR S508 3 Ton Low Profile Floor Jack: lift range, specs and fit

The VEVOR S508 is a hydraulic trolley (floor) jack rated at 3 tons, built low so it can reach under cars with limited ground clearance. It is meant for jobs such as wheel changes, oil changes and brake work in a home garage or small workshop. Here is what its specifications mean and what to confirm for your own vehicle.

Capacity and lifting range

VEVOR lists the capacity as 3 tons (6,600 lb). It is the load the jack is rated to lift, not the weight of the whole vehicle, because a jack typically raises one end or one corner at a time. The listing says the range suits family cars, trucks and SUVs.

The minimum height is 5.12 inches (130 mm) and the maximum is 20 inches (508 mm). The low minimum lets the saddle slide under lower vehicles; the 20-inch top gives reach for taller trucks and SUVs. Check the lifting points and ground clearance of your own vehicle against those two figures.

The quick-lift pump

A single-piston quick-lift pump brings the saddle up to the vehicle in fewer strokes, then the jack lifts the load as you continue pumping. VEVOR says it lets you reach the desired height easily. Hydraulic jacks of this type use a sealed oil system, and the listing mentions a sealing system for long-term use.

Saddle, handle and wheels

A rubber saddle sits where the jack meets the vehicle, and VEVOR says it protects the vehicle. The saddle rotates 360° and can be detached and replaced. The handle is 45 inches (1,145 mm) long, and longer handles typically give more leverage. It is a two-piece design that comes apart for storage. The listing includes a tip: loosen the handle's limit bolt before use so the handle doesn't slip out, and tighten it once the handle is fully inserted.

The jack has steel wheels, and VEVOR says the two rear wheels are universal swivel types, which helps with steering and rolling it into position.

Construction and standards

The frame is heavy-duty steel. VEVOR lists compliance with CE (2006/42/EC, EN 1494), UKCA (SI 2008 No. 1597, BS EN 1494) and the ASME PALD-2014 safety standard, and says the jack has a built-in safety load system that prevents use beyond its capacity. Treat those as the brand's statements, and read the manual for the exact limits.

The listing gives the size as 28.7 x 14.6 x 9.1 inches and the weight as 69 lb. That is a substantial tool, so allow garage floor space and think about how you'll move it.

Who it suits

The jack suits DIY owners and enthusiasts who do their own tyre rotations, oil changes and brake jobs and who want a low-profile design. If you have a very heavy vehicle, check its weight and recommended lift points before choosing.

What to check before you buy

• Vehicle weight and lift points: confirm the manufacturer's recommended jacking points and weight.
• Ground clearance: compare your vehicle's clearance with the 5.12-inch minimum.
• Height: compare the 20-inch maximum with the height you need.
• Stands: a jack is for lifting, not holding. The standard advice is to support a raised vehicle on correctly rated jack stands, on a flat, firm surface, and to follow the manual and local guidance.
• Storage and handling: it weighs 69 lb, and the handle splits in two for storage.
• Upkeep: check the manual for oil checks, lubrication and what to do if the pump feels spongy.

The short version

• A hydraulic low-profile floor jack rated by VEVOR at 3 tons (6,600 lb).
• Lifts from 5.12 to 20 inches with a single-piston quick-lift pump.
• 360° rotating rubber saddle and a 45-inch two-piece handle.
• Listed standards: CE (EN 1494), UKCA (BS EN 1494) and ASME PALD-2014, with a built-in safety load system.
• 69 lb with steel wheels, so plan where it will be stored.

Bloiq is reader-supported. Some links may earn us a commission; it never affects what we write. How we make money.