VEVOR 12V Air Compressor with 0.8 Gal Tank: features, specs and uses

This VEVOR 12V kit pairs a small air compressor with a 0.8-gallon (3 L) tank. It is designed to be mounted on a vehicle and run from its 12V battery system. The main use is feeding train air horns, which need a stored supply of air, but VEVOR also lists inflating tyres and air mattresses.

Why a tank matters for air horns

A train horn uses a large burst of air for a short time. A compressor alone usually can't provide that flow, so a tank stores air at pressure and releases it quickly when the horn is sounded. The compressor then refills the tank. A 3 L tank gives a modest reserve, so check that the horn you plan to run is suitable for such a small reservoir. Check local rules too, since vehicle horns are regulated in many places.

Pressure range and automatic control

VEVOR says the system works between 90 and 120 psi. It starts inflating below 90 psi and stops above 120 psi, preventing overpressure. A gauge shows pressure in real time. This cut-in and cut-out behaviour is how most onboard systems keep a tank topped up without attention.

The kit also has fuses to protect the compressor, and a drain plug for releasing water. Compressing air creates condensation, which collects in the tank, so draining it from time to time is standard upkeep.

Motor and materials

The listing quotes a motor speed of 5,000 r/min. The tank is described as heavy-duty steel with an anti-rust coating and a tightly welded, non-leaking structure. A PA gas pipe is rated to withstand temperatures up to 120°C, and the motor has a 100°C temperature-controlled overload protection. Heat tolerance matters on a vehicle, where the engine bay and underbody can get hot.

Mounting and vibration

A thick rubber cushion is meant to sit between the tank and the vehicle's underside. VEVOR says it reduces noise and adds stability. Vehicles vibrate constantly, so secure mounting and tight connections matter. The unit measures about 13.0 x 5.5 x 7.9 inches (33 x 14 x 20 cm) and weighs 9.9 lb (about 4.5 kg).

Fitting the vehicle

The compressor suits any vehicle with a 12V battery system, and VEVOR lists trucks, SUVs and cruise ships. The listing doesn't give current draw, so check the manual for the wire gauge, fuse size and relay requirements. A compressor motor draws considerable current while running.

Other uses

With a suitable hose and fitting, the tank and compressor can inflate tyres or air mattresses, as VEVOR says. At 120 psi maximum it is not a tool for high-pressure work. It is not described as a replacement for a workshop compressor for tools that need continuous airflow, since a 0.8-gallon tank runs out quickly.

Who it suits

It suits vehicle owners fitting air horns, as well as people who want an onboard air supply for occasional inflation. Installation involves wiring and mounting, which many owners hand to a qualified installer.

What to check before you buy

• Horn compatibility: check your horn's air consumption and pressure against the tank and 120 psi.
• Mounting space: find a spot for the tank and compressor with airflow and protection from water.
• Wiring: plan the cable size, fuse and switch or relay to the manual's specification.
• Fittings: confirm thread sizes and hoses for the accessories you want.
• Drainage: place the drain plug where you can reach it.
• Local rules: some places limit the loudness or type of vehicle horns.

The short version

• A 12V onboard air compressor with a 0.8-gallon (3 L) steel tank.
• Automatic range of 90 to 120 psi with a pressure gauge.
• Fuses, a drain plug, rubber mounting cushion and overload protection at 100°C.
• Intended for train air horns, tyres and air mattresses.
• Weighs 9.9 lb; check wiring and local horn rules before installing.

Bloiq is reader-supported. Some links may earn us a commission; it never affects what we write. How we make money.